View YB15KKG01_4581238.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

Short Body Pushbuttons
Series YB
Distinctive Characteristics
Combination bezel-barrier is an integral part of the switch and prevents accidental actuation. Unique thermoplastic elastomer seal inside caps plus rolled sleeve of nitrile butadiene rubber at joining of housing and inner case, all for added protection to interior mechanism. Dust and oil tight as well as splashproof panel seal models qualify to IP65 of IEC60529 Standards (similar to NEMA 4 and 13). Panel seal models provided with exterior o-ring. Distinctive design of snap-action contacts for shock resistance, long life, and sensitive actuation. High density design to give behind panel depth of less than one inch. Terminals are epoxy sealed to lock out flux, dust, solvents, and other contaminants. Latchdown for indication of circuit status, plus audible, tactile feedback with smooth, responsive operation. Illuminated models available and shown in the Illuminated Pushbutton section. Matching indicators available and shown at the end of Section M.
Actual Size
NKK Switches * email: sales@nkkswitches.com * Phone (480) 991-0942 * Fax (480) 998-1435 * www.nkkswitches.com
08-08
Short Body Pushbuttons
Series YB
General Specifications
Electrical Capacity (Resistive Load)
Power Level (silver): Logic Level (gold): 3A @ 125V AC or 3A @ 250V AC or 3A @ 30V DC 0.4VA maximum @ 28V AC/DC maximum (Applicable Range 0.1mA ~ 0.1A @ 20mV ~ 28V) Note: Find additional explanation of operating range in Supplement section.
Other Ratings
Contact Resistance: Insulation Resistance: Dielectric Strength: Mechanical Life:
Electrical Life: Nominal Operating Force: Contact Timing: Travel:
50 milliohms maximum for silver; 100 milliohms maximum for gold 200 megohms minimum @ 500V DC 1,000V AC minimum between contacts for 1 minute minimum; 1,500V AC minimum between contacts & case for 1 minute minimum 1,000,000 operations minimum for momentary circuit 200,000 operations minimum for maintained circuit 100,000 operations minimum Single pole: 1.47N for nonsealed; 1.67N for sealed Double pole: 2.75N for nonsealed; 2.94N for sealed Nonshorting (break-before-make) Pretravel .059" (1.5mm); Overtravel .059" (1.5mm); Total Travel .118" (3.0mm)
Materials & Finishes
Housing/Bezel: Snap-in Frame: Base: Movable Contactor: Movable Contacts: Stationary Contacts: Terminals:
Glass fiber reinforced polyamide (UL94V-0) Stainless steel Diallyl phthalate resin (UL94V-0) Phosphor bronze with silver or gold plating Silver alloy with silver plating or brass with gold plating Silver alloy or copper with gold plating Phosphor bronze with tin plating
Environmental Data
Operating Temp Range: Humidity: Vibration: Shock: Sealing:
-25C through +70C (-13F through +158F) 90 ~ 95% humidity for 96 hours @ 40C (104F) 10 ~ 55Hz with peak-to-peak amplitude of 1.5mm traversing the frequency range & returning in 1 minute; 3 right angled directions for 2 hours 50G (490m/s2) acceleration (tested in 6 right angled directions, with 5 shocks in each direction) IP65 of IEC60529 standard for panel seal models
Installation
Mounting Torque: Soldering Time & Temperature:
0.785Nm (6.95 lb*in) maximum Manual Soldering: See Profile A in Supplement section.
Standards & Certifications
Flammability Standards: UL & C-UL Recognized:
R
CSA Certified:
UL94V-0 housing & base All solder lug models recognized at 3A @ 125/250V AC or 0.4VA @ 28V AC/DC maximum; UL File No. WOYR2.E44145; add "/U" to end of part number to order UL mark on switch; C-UL File No. WOYR8.E44145; add "/C-UL" to end of part number to order C-UL mark on switch. All solder lug models certified at 3A @ 125/250V AC or 0.4VA @ 28V AC/DC maximum; CSA File Nos. 023535-0-000; add "/C" to end of part number to order CSA mark on switch.
NKK Switches * email: sales@nkkswitches.com * Phone (480) 991-0942 * Fax (480) 998-1435 * www.nkkswitches.com
08-08
Short Body Pushbuttons
TYPICAL SWITCH ORDERING EXAMPLE
Series YB FB
YB
POLES
1 2 SPDT DPDT
1
5
SHAPES
Bushing Mounting S C R K M N Square Round Rectangular Square Round Rectangular
C
K
W
01
CONTACT MATERIALS & RATINGS
W G Silver Rated 3A @ 125V AC Gold Rated 0.4VA max. @ 28V AC/DC max.
Snap-in Mounting
CIRCUITS
5 6 ON ON (ON) ON ( ) = Momentary Alternate Action with Latchdown
TERMINALS
01 03 Solder Lug/.110" (2.8mm) Quick Connect Straight PC
HOUSING
K Black only BB
CAP COLORS
White/White Red/White Yellow/White Green/White Blue/White CB EB FB GB
PANEL SEAL
No Without Panel Seal Code W With Panel Seal (Bushing Mount only)
IMPORTANT:
Switches are supplied without UL, C-UL, & CSA markings unless specified. Specific models & ratings noted on General Specifications page.
Note: Cap with clear lens and colored insert available; see Illuminated Pushbuttons section
DESCRIPTION FOR TYPICAL ORDERING EXAMPLE
YB15CKW01-FB
Round with Bushing Mounting Black Housing SPDT ON-(ON) Circuit
Cap with Green Lens & White Insert Without Panel Seal Silver Contacts with 3 Amp Rating Solder Lug/.110" (2.8mm) Quick Connect Terminals
NKK Switches * email: sales@nkkswitches.com * Phone (480) 991-0942 * Fax (480) 998-1435 * www.nkkswitches.com
08-08
Short Body Pushbuttons
POLES & CIRCUITS
Plunger Position ( ) = Momentary Normal Pole SP DP Model YB15 *YB16 YB25 *YB26 ON ON ON ON (ON) ON (ON) ON 1-3 1-3 4-6 1-2 1-2 4-5 Down Connected Terminals Normal Down Note:
Series YB
Throw & Schematics Switch is marked with NC, NO, COM, L+, L-.
1 (COM)
SPDT DPDT
3 1 (COM) 3 2 6
2 4 5
* When in latchdown position for the alternate circuit, cap position is .020" (0.5mm) above the built-in bezel.
PANEL SEAL No Code
Bushing Mounting Without Panel Seal Snap-in Mounting
W
With Panel Seal
Bushing Mounting only Supplied with mounting nut and o-ring AT089.
Supplied with mounting nut.
SHAPES & MOUNTING TYPES
Bushing Mounting Snap-in Mounting
S
Square
C
Round
R
Rectangular
K
Square
M
Round
N
Rectangular
Bezel-barrier is an integral part of the switch body.
HOUSING K
Black Housing available in black only. The 1-piece body and bezel-barrier have a matte finish.
CONTACT MATERIALS & RATINGS W G
Silver Contacts Gold Contacts Power Level Logic Level 3A @ 125/250V AC 0.4VA max. @ 28V AC/DC max.
Complete explanation of operating range in Supplement section.
NKK Switches * email: sales@nkkswitches.com * Phone (480) 991-0942 * Fax (480) 998-1435 * www.nkkswitches.com 08-08
Short Body Pushbuttons
TERMINALS 01
Solder Lug/ .110" (2.8mm) Quick Connect
Epoxy Seal (7.3) .288
Series YB
(2.0) (2.8) .079 .110 (1.2) .047 Thk = (0.5) .020
03
Straight PC
Epoxy Seal (0.6) R .024 (4.4) .173 (2.8) .110
3 2
(3.7) Typ .146
5
6
3 2
(3.7) Typ .146
(1.2) .047 Thk = (0.5) .020
Single Pole
(3.0) .118
1
(4.85) Typ .191 (1.6) Dia Typ .063
Double Pole
4
1
(4.85) Typ .191 (1.6) Dia Typ .063 (5.55) Typ .219
(5.55) C .219 L
(3.0) Typ .118 C L
CAPS & COLORS
Colors Available: AT3002 Round
(15.0) Dia .591 (12.2) .480 (4.0) .157
BB CB EB FB GB
White/ White Red/ White Yellow/ White Green/ White Blue/ White
AT3001 Square
(15.0) Sq .591 (12.2) .480 (4.0) .157
AT3003 Rectangular
(15.0) .591 (21.0) .827
(12.2) .480 (4.0) .157
Materials: Lens & Insert: Polycarbonate Seal/Filter: Thermoplastic Elastomer
TYPICAL SWITCH DIMENSIONS
Square * Bushing Mounting Single & Double Pole
(9.4) .370 M15.8 P1 (1.2) x (2.0) Typ .047 x .079 (0.5) Typ .020
NO
(3.7) .146
3 2
NC L -+
6 5 4
NO
(9.7) .382
(2.8) Typ .110 (15.0) Sq .591 (18.0) Sq .709 (10.9) .429 (7.3) .288
1
COM
(8.3) .327
(24.3) .957
(6.0) .236 (11.1) .437
YB15SKW01-CB
Single pole models do not have terminals 4, 5, & 6. 08-08
NKK Switches * email: sales@nkkswitches.com * Phone (480) 991-0942 * Fax (480) 998-1435 * www.nkkswitches.com
Short Body Pushbuttons
TYPICAL SWITCH DIMENSIONS
Round * Panel Seal Single & Double Pole
(9.4) .370 (1.2) x (2.0) Typ .047 x .079 (0.5) Typ .020
Series YB
(0.5) .020
M15.8 P1
(3.7) .146
NO
3 2
NC L -+
6 5 4
NO
(9.7) .382
(2.8) Typ .110 (15.0) Dia .591 (18.0) Dia .709 (0.5) .020 (3.0) .118 (10.9) .429 (5.3) (24.3) .209 .957 Latchdown Position (7.3) .288
1
COM
(6.0) .236 (11.1) .437
YB25WCKW01-EB
Single pole models do not have terminals 4, 5, & 6.
Rectangular * Snap-in Mounting
Single & Double Pole
(1.2) x (2.0) Typ .047 x .079 (0.5) Typ .020 (3.7) .146
(15.0) .591 (18.0) .709
NO
3 2
NC L -+
6 5 4
NO
(9.7) .382
(2.8) Typ .110 (21.0) .827 (24.0) .945 (7.3) .288 (8.3) .327 (24.3) .957
1
COM
(6.0) .236 (11.1) .437
YB15NKW01-CB
Single pole models do not have terminals 4, 5, & 6.
PANEL THICKNESS & CUTOUTS
Bushing & Panel Seal Mount Snap-in Mount
Panel Thickness .020" ~ .197" (0.5mm ~ 5.0mm)
(16.0) .630
+ 0.2 - 0.0
Panel Thickness .039" ~ .138" (1.0mm ~ 3.5mm)
Dia
(1.2) R .047
0.2 (16.0) + 0.0 Dia - .630
AT106 Socket Wrench for Bushing Mounting Material: Aluminum with black alumite finish
(16.0) Dia .630 (18.0) Dia .709 (60.0) 2.362 (57.5) 2.264
Note: Overtightening the mounting nut AT092 may damage the switch housing.
NKK Switches * email: sales@nkkswitches.com * Phone (480) 991-0942 * Fax (480) 998-1435 * www.nkkswitches.com
08-08
Short Body Pushbuttons
OPTIONAL ACCESSORIES
Series YB
Dust Covers and Protective Guards reduce depth of switch behind panel by .047" (1.2mm). Panel Thickness Range with Dust Cover or Protective Guards: Bushing Mounting .020" ~ .150" (0.5mm ~ 3.8mm) Snap-in Mounting .020" ~ .091" (0.5mm ~ 2.3mm) Dust/Splash Cover AT4115 Dust Cover for Snap-in or Bushing Mount AT4115 Splash Cover and AT541 O-ring for Bushing Mount Materials: Lid: Polyvinyl Chloride Base: Polyamide O-ring: Nitrile butadiene rubber Snap-in Mount Panel Seal Dust Cover
AT4115 AT089 AT541
(5.2) .205
Panel Seal .020" ~ .118" (0.5mm ~ 3.0mm)
(16.2) .638 (5.9) .232
Splash Cover
AT4115
(23.2) .913 (16.0) Dia .630
(29.2) 1.150
AT4115
Note: AT089 o-ring supplied with panel seal model. Protective Guard
(20.0) Dia .787 (0.5) .020
AT541
AT4072 Protective Guard Opens 90 Closes manually
(22.9) .902
Assembled Cap Height
(1.2) .047
(12.0) .472
Materials: Lid: Polycarbonate Base: Glass Fiber Reinforced Polycarbonate
(1.2) .047 (23.9) .941
(6.6) .260 (11.2) .441
(16.0) Dia .630
Spring Loaded Protective Guard AT4175 Spring Loaded Protective Guard Opens 180 Closes automatically
(23.4) .921 (16.0) Dia .630 Assembled Bezel Height
(12.5) .492
(45.0) Min* 1.772 AT4175 (23.9) .941 (11.4) .449
(1.2) .047
(16.0) Dia .630 180
(12.5) .492 (23.4) .921
(23.9) .941
(24.0) Min .945
Materials: Lid: Polycarbonate Base: Glass Fiber Reinforced Polyamide Coil Spring: Stainless Steel
* Minimum dimension allows opening of cover to 180
NKK Switches * email: sales@nkkswitches.com * Phone (480) 991-0942 * Fax (480) 998-1435 * www.nkkswitches.com
08-08
Short Body Pushbuttons
LEGENDS
Series YB
Easily create and submit your own legends using our new on-line Legend Maker. Visit www.nkkswitches.com
For other legend support options, customers may either contact the factory and request the YB Legend Packet, or utilize the general information and basic specifications presented below.
Additional methods for legends are engraving the lens and laser printing on film inserts. Maximum depth for engraving is .012" (0.3 mm) on the cap lens. Enamel paint is recommended to fill the engraved area.
NKK Switches * email: sales@nkkswitches.com * Phone (480) 991-0942 * Fax (480) 998-1435 * www.nkkswitches.com
LM
Suggested Printable Area for YB Lens Recommended Methods: Laser Etch on clear lens; Screen Print or Pad Print on lens. Epoxy based ink is recommended.
(13.48) (15.0) .531 .591
ON
(13.48) Sq .531 (15.0) Sq .591 (0.76) Typ .030 (13.48) Dia .531 (15.0) Dia .591 (0.76) Typ .030 (0.76) Typ .030 (19.48) .767 (21.0) .827
(0.76) Typ .030
Shaded Areas Are Printable Areas Additional Methods
08-08

▲Up To Search▲

Price & Availability of YB15KKG01

	To Download YB15KKG01 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .